With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
This self-clamping table saw fence takes only seconds to put on and lets you crank the blade into the fence to create both angled cuts along board edges and extremely thin rip or rabbet cuts. With a hand- or jigsaw, cut pieces from a 1×4, making the inside width of the “L” a hair under the thickness of your saw’s fence. Drill 5/16-in. holes in the L-blocks and plywood fence and join them with two 1/4-in. x 3-in. countersunk machine screws, washers and Wing-Nuts. As always, use extra caution when you’re sawing without a blade guard. Our thanks for this new sawing angle to professional furniture maker George Vondriska. Check out these 16 genius tool hacks you need to know!
You can transfer a graphic on any wood piece of your choice, including a frame, top of a table, etc. The surface should be clean and big enough for the graphic paper. I am also sharing a video tutorial here that explains in detail the process of transferring any graphic to a wooden surface using a freezer paper. Just gather the items you need and follow this video to carve your favorite designs on your favorite wood items.
Particleboard is a manufactured wood product composed of sawdust, wood chips or wood shavings mixed with a resin. This concoction is layered, compressed, subjected to heat and cut to shape, resulting in a sheet material that can be used for a variety of things. It’s often used as shelving or as an underlayment for carpet. Plastic laminate may be applied to both sides to create a product that can be used to create everything from furniture to cabinets to wall paneling. Head into IKEA and you’ll find acres of particleboard.
Afrormosia Alder Andiroba Anigre Ash Apple Aspen Avodire Balsa Beech Bilinga Birch African Blackwood Australian Blackwood Boxwood Bubinga Camphor Cedrela Cherry Chestnut Cocobolo Cumaru Ebony Elm Eucalyptus Hazel Hickory Hornbeam Idigbo Imbuia Ipê Iroko Jarra Jelutong Lignum vitae Linden (lime, basswood) Merbau Mahogany (American, African) Maple Meranti Oak Padauk Pear Plum Poplar Purpleheart Ovankol Ramin Red Quebracho Rosewood Rubberwood Sapele Teak Totara Utile Walnut Wenge Willow Zebrano
For many of us, the moment we learned that a 2×4 board is actually 1.5 inches x 3.5 inches was simply mind-blowing. The reason for this apparent contradiction is that the board has been planed down to eliminate irregularities. At one point, many years ago, 2x4s actually were 2 inches x 4 inches, but their rough surfaces made them difficult to stock and handle. The old terms, such as 2×4 or 4×4, are still used, and are known as the “nominal” size of the board. These nominal sizes are used because they are easier to say and they stick to tradition. Now, thanks to a lawsuit, most big box stores list the nominal and actual sizes of lumber.
Here’s a safe and sound way to make long cuts with a circular saw on plywood clamped to a worktable. Cut about 12 in. into the plywood, then twist a piece of duct tape into a bow tie, with up-and-down adhesive faces. Slide it in the saw kerf and press the tape down above and under the plywood. Now as you finish the cut, the trailing end can’t curl down dangerously as you saw. Hats off to Mike Connelly for simplifying this job. Check out how to make this DIY duct tape wallet.
While many woods can be used for carving, there are some clear favorites, including Aspen, Basswood, Butternut, Black Walnut, and Oak. Because it has almost no grain and is notably soft, Basswood is particularly popular with beginner carvers. It is used in many lower-cost instruments like guitars and electric basses. Aspen is similarly soft, although slightly harder, and readily available and inexpensive. Butternut has a deeper hue than Basswood and Aspen and has a nice grain that is easy to carve, and thus friendly for beginners. It's also suitable for furniture. While more expensive that Basswood, Aspen, and Butternut, Black Walnut is a popular choice for its rich color and grain. Lastly, Oak is a strong, sturdy, and versatile wood for carving with a defined grain. It's also a popular wood for furniture making.