Pocket screws create a solid, simple-to-make joint. Because of the size and visibility of the hole, it’s usually located in areas that are concealed or rarely seen (though special plugs can be used to fill the holes.) Craig Sommerfeld, founder of The Kreg Tool Company, is credited with popularizing pocket screw joinery in the 1980s. The company today is the leader in creating the jigs, clamps and screws used to create pocket screw joints. Learn how to use a pocket screw jig in woodworking projects.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.

Another awesome thing about this coffee table is that it is also has a storage unit. So you can store drinks, and other stuff in the half barrel of your table and then close or open it whenever you need. Pete has also constructed a video for this tutorial for which you can find the link below. It illustrates the same process in a video guide that shows you the exact process to be followed while building this whiskey barrel coffee table.
Finding affordable lumber has always been a mainstay for woodworkers, and when you tie our dwindling natural resources into the conversation the time is right to look at milling your own lumber. This seven-part weekly video series takes you through how to find lumber, how to operate a sawmill, details on types of sawing methods, stickering and drying and ultimately advice on using a mill as part of a business. Learn what you need to know to understand Milling Your Own Lumber.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
					          See Products            See Products            See Products            See Products            See Products            See Products            See Products            See Products            See Products            See Products            See Products            See Products            See Products            See Products            See Products   

I built my first platform bed by following the steps mentioned in the tutorial and the end result was everything I expected. It was as beautiful as comfortable and strong. It only cost me around $60 to build this one from the scratch. And if I can build it, anyone can. What you need is a little bit of woodworking experience and a lot of confidence. Collect the items as suggested in the video and start working now.
Historically, woodworkers relied upon the woods native to their region, until transportation and trade innovations made more exotic woods available to the craftsman. Woods are typically sorted into three basic types: hardwoods typified by tight grain and derived from broadleaf trees, softwoods from coniferous trees, and man-made materials such as plywood and MDF.

Brazos is committed to providing the highest quality with superior service. Many of our team members have 30 plus years experience in the hardwood industry and that makes Brazos Forest Products the clear leader for hardwood distribution in Texas and Louisiana. Quality, Service and Commitment are what Brazos strives for each and every day to take care of our customers. This makes Brazos Forest Products the clear choice for all your Hardwood, Plywood and Custom Moulding needs.

Finding a toolbox for a mechanic, for his hand tools, is not a big challenge at all - there are dozens of the tool boxes available on the market, from huge roll-around shop cases to small metal boxes. Plumbers, electricians, and farmers are well served, too, with everything from pickup-truck storage to toolboxes and belts. But, if you are a shop-bound woodworker then the case changes. You get to need a tool box that suits the range and variety of hand tools that most woodworkers like to have. For those who deny making do with second best, there's only one solution, you’ve to build a wooden toolbox that should be designed expressly for a woodworking shop.

The shelf in the first picture is made of red oak plywood. You can choose the wood type, color and design as you like for your project. In case if you need more help understanding this project, you can refer the source link below. It discusses various items used, steps and tips and personal experience of the author who personally built a Zigzag shelf.
My planer blasts shavings all over the shop floor. I decided to make my own dust chute from 4-in. PVC sewer pipe (which has thinner walls than regular Schedule 40 pipe) and a couple caps. I cut a slit in the pipe and used a heat gun to soften the plastic. That allowed me to open the slit. (Heating PVC releases fumes; ventilation is critical.) I then drilled holes in the flap and screwed it to the planer housing. Finally, I cut a 2-1/2- in. hole in one of the end caps to accept my shop vacuum hose. Works great! — Luis Arce. Here’s what else you can do with PVC pipe.
Furnishing and decorating your patio is not an easy task – but then again, it has to be done! Your patio is obviously one of the most important rooms in your home, as you can easily turn it into your little piece of Heaven, your “safe spot” in your home where you can retreat whenever you want to ignore the world and just spend some time alone all by yourself.

You can also make one for elders and put it in your garden or terrace or anywhere in the house. Elders can use it to relax and kids can use it to play or sleep. Although this is a really beautiful piece of woodwork, it is not that easy to make. Only someone with good woodworking skill can think of making this swing set. Also, I couldn’t find a good tutorial that illustrates the process of building a wooden boat-shaped swing set. Most Probably, I will write one when I build mine.But if you really want this swing set like right now, I would suggest you hire a good woodworker, who can build something similar. Or just search the internet and maybe you get lucky enough to find a tutorial for this. Good luck either way.

“I do a lot of finish-sanding freehand, without a sandpaper block, so I can smooth edges and get into nooks and crannies. But the finer grits are usually bonded to thinner paper and, at least for me, the paper is too thin and ends up tearing long before the grit wears out. So I apply duct tape to the back of the sandpaper. The sandpaper is still flexible enough to sand a tight radius and it’s far more durable. You can use this super-strong sandpaper like a shoeshine rag.” — Chuck Merchant
Use whatever image hosting service you like and post the link to /r/woodworking. The key here is it needs to be apparent that you've built the entry, and you follow the photo requirements listed in the contest rules. Submissions of finished photos only will not be accepted for entry. <-- I can't emphasize this enough, you absolutely need more than 2-3 photos for a valid submission. I will no longer accept entries that have albums that go from rough stock to 90% complete in one jump.
Often times at first glance a board looks straight and the fact that it is actually bowed or has some warping isn’t always obvious. So the trick to knowing for sure, is to hold the board up towards your face, with the other end on the ground, and look at it at a downward angle (as shown in the below photo). This method will allow you to see if it is bowing at all. 

Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.

This particular tray is made using reclaimed barn wood but the author of the project Beyond The Picket Fence surprised everyone with one fact: reclaimed barn wood has often some areas turned pink due to cow urine. If you check the project more closely, you’ll also notice some areas of the tray being almost bright pink. That’s something you don’t see every day!
Historically, woodworkers relied upon the woods native to their region, until transportation and trade innovations made more exotic woods available to the craftsman. Woods are typically sorted into three basic types: hardwoods typified by tight grain and derived from broadleaf trees, softwoods from coniferous trees, and man-made materials such as plywood and MDF.

Another awesome thing about this coffee table is that it is also has a storage unit. So you can store drinks, and other stuff in the half barrel of your table and then close or open it whenever you need. Pete has also constructed a video for this tutorial for which you can find the link below. It illustrates the same process in a video guide that shows you the exact process to be followed while building this whiskey barrel coffee table.


Whether you're new to woodworking or you've been doing it for years, Woodcraft's selection of woodworking projects is one the best places to find your next big project. Whether you're looking to make wooden furniture, pens, toys, jewelry boxes, or any other project in between, the avid woodworker is sure to find his or her next masterpiece here. Find hundreds of detailed woodworking plans with highly accurate illustrations, instructions, and dimensions. Be sure to check out our Make Something blog to learn expert insights and inspiration for your next woodworking project.
The best thing about the toy chest is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can also modify your kid’s toy chest in any way you want or build in a different design or color different from the one pictured above. You can try some other designs for your plan in the below-mentioned link.
Cedars are strong, aromatic softwoods that are capable of enduring outdoor elements, the most common of which is the Western Red Cedar. Western Red Cedar can sustain wet environments without succumbing to rot, and as a result is commonly used for outdoor projects such as patios, outdoor furniture, and building exteriors. This wood can be easily found at most home centers for a moderate price.[12]
This rack can be built from old unused wood pallets you can find around the house. So it is also a great way to recycle those old pallets. You can also find a step by step tutorial at instructables.com for which I have included the source link below. This tutorial helps you to make a wood wine rack from the scratch. So what are waiting for? Just grab the items you need and start building a cool wooden rack for those nice wine bottles of yours.

Here, I am writing about another DIY project that involves the use of an old furniture piece. I think that the idea of reusing and recycling old furniture has got to me. Anyways, I am starting to love it. This project involves using an old door to build a beautiful multi picture frame, as you can see in the image below. This frame looks really wonderful and can be used to hold many pictures at a time.
Finally, properly preparing your wood surface is super important. It will make a huge difference when it comes times to stain, paint, or finish your wood. There are a lot of tips for wood surface preparation, but sanding the wood is one of the most important steps. And I find it really helpful to do the bulk of my sanding before I start ripping (cutting) and building with my wood since it’s still in whole pieces. You can check out my simple tips for how to sand wood in my how to stain wood tutorial, which is also good to reference if you need to learn how to stain too!
Hardwoods are separated into two categories, temperate and tropical hardwoods, depending on their origin. Temperate hardwoods are found in the regions between the tropics and poles, and are of particular interest to wood workers for their cost-effective aesthetic appeal and sustainable sources.[9] Tropical hardwoods are found within the equatorial belt, including Africa, Asia, and South America. Hardwoods flaunt a higher density, around 65lb/cu ft as a result of slower growing rates and is more stable when drying.[9] As a result of its high density, hardwoods are typically heavier than softwoods but can also be more brittle.[9] While there are an abundant number of hardwood species, only 200 are common enough and pliable enough to be used for woodworking.[11] Hardwoods have a wide variety of properties, making it easy to find a hardwood to suit nearly any purpose, but they are especially suitable for outdoor use due to their strength and resilience to rot and decay.[9] The coloring of hardwoods ranges from light to very dark, making it especially versatile for aesthetic purposes. However, because hardwoods are more closely grained, they are typically harder to work than softwoods. They are also harder to acquire in the United States and, as a result, are more expensive.[9]
×