A while back, I reached for my two containers of epoxy and noticed that the resin in one container had crystallized exactly like honey that’s been in the cupboard too long. The solution is exactly the same too: Set the container in a bowl of hot tap water. After about 15 minutes, I emptied the container and refilled it with hot water. After about a half hour, the epoxy regained its normal consistency. Good as new! — Ken Holte

Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.
Here, I am writing about another DIY project that involves the use of an old furniture piece. I think that the idea of reusing and recycling old furniture has got to me. Anyways, I am starting to love it. This project involves using an old door to build a beautiful multi picture frame, as you can see in the image below. This frame looks really wonderful and can be used to hold many pictures at a time.
With an orbital sander and good sandpaper you can smooth wood evenly and easily with first-class results. When flush-sanding solid edge-banding, draw a squiggly line across the joint before sanding. The edge-banding will be slightly proud of the plywood veneer, so the pencil marks provide a visual aid to make sure that you’re sanding flat, and that you don’t sand through the plywood’s veneer. As you go, you can also test for a smooth, level transition by gently scraping your fingernails against the transition. If it’s smooth, your fingers will not catch on the seam between the two pieces
Here’s a safe and sound way to make long cuts with a circular saw on plywood clamped to a worktable. Cut about 12 in. into the plywood, then twist a piece of duct tape into a bow tie, with up-and-down adhesive faces. Slide it in the saw kerf and press the tape down above and under the plywood. Now as you finish the cut, the trailing end can’t curl down dangerously as you saw. Hats off to Mike Connelly for simplifying this job. Check out how to make this DIY duct tape wallet.
See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products
Old doors laid across sawhorses make great temporary workbenches, but they take up a lot of space when you’re not using them. Instead of full-size doors, I use bifold doors with hinges so I can fold them up when I’m done working. They’re also easier to haul around in the pickup for on-the-road jobs. — Harry Steele. Here are 12 more simple workbenches you can build.
We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it!
Finally, properly preparing your wood surface is super important. It will make a huge difference when it comes times to stain, paint, or finish your wood. There are a lot of tips for wood surface preparation, but sanding the wood is one of the most important steps. And I find it really helpful to do the bulk of my sanding before I start ripping (cutting) and building with my wood since it’s still in whole pieces. You can check out my simple tips for how to sand wood in my how to stain wood tutorial, which is also good to reference if you need to learn how to stain too!
The procedure is very easy to understand and follow for anyone with a little woodworking knowledge. Make sure to collect all the items you need before you start with the project. You may even ask Tracy your queries directly in the comment section of the tutorial post. Or you can ask them here. Either way, I hope that you manage to build this one nicely.
Here’s an easier way to stain or seal chairs, lattice or anything with numerous tight recesses. Pour the stain into a clean, empty spray bottle ($3). Spray the stain onto the project and wipe up the excess with a brush or rag. The sprayer will squirt stain into all those tight, hard-to-reach cracks and joints. — Valrie Schuster. Learn more about staining wood.

The rubber cushion on my old palm sander was wearing thin around the edges. Because of its age, I couldn’t find a replacement pad. As I was drinking my beverage with a foam can cover around it, I realized I could cut the foam to fit the sander and glue it on. I peeled off the old pad, cleaned the metal base and attached the foam with contact cement. Works for clamp-on as well as stick-on sanding squares! You can find can covers at discount and convenience stores. — Allen J. Muldoon


The shelf in the first picture is made of red oak plywood. You can choose the wood type, color and design as you like for your project. In case if you need more help understanding this project, you can refer the source link below. It discusses various items used, steps and tips and personal experience of the author who personally built a Zigzag shelf.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
Second, learning how to read lumber dimensions, like knowing what 1×2 or 2×12 actually means, is really important. Understanding softwood lumber dimensions will help you to read woodworking build plans, shop for lumber, and understand the general measurements for your projects. I’ve provided a simple explanation to lumber sizes along with a free lumber size chart printable here!
Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.
×