With two varieties, red and white, oak is known to be easy to work with and relatively strong. However, furniture makers often opt for white oak over red oak for its attractive figure and moisture-resistance.[12] Depending on the kind needed, oak can probably be found at a local home center or a lumberyard for a bit pricier than other hardwoods.[12][13]
Hard to determine which stain you need in that bespattered collection of cans? An easy-to-make “stain index,” courtesy of reader Bob Jacek, solves the problem. Section off boards of your favorite woods into squares with masking tape, and apply the different stains across the width of each wood type (pine, oak, birch, etc.). When the stains are dry, brush on lengthwise your regular finishes—polyurethane, water-based polyurethane, oil, orange shellac, etc. You’ll be able to tell how each stain looks with each finish. Label each one. Use both sides of each board, and you’ll have a wooden encyclopedia of stain and finish combinations. Plus: How to stain wood evenly.

While many woods can be used for carving, there are some clear favorites, including Aspen, Basswood, Butternut, Black Walnut, and Oak.[14] Because it has almost no grain and is notably soft, Basswood is particularly popular with beginner carvers. It is used in many lower-cost instruments like guitars and electric basses.[14] Aspen is similarly soft, although slightly harder, and readily available and inexpensive.[14] Butternut has a deeper hue than Basswood and Aspen and has a nice grain that is easy to carve, and thus friendly for beginners. It's also suitable for furniture.[14] While more expensive that Basswood, Aspen, and Butternut, Black Walnut is a popular choice for its rich color and grain.[14] Lastly, Oak is a strong, sturdy, and versatile wood for carving with a defined grain. It's also a popular wood for furniture making.[14]
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
Cutting sandpaper is a quick way to dull your scissors or utility knife blade. Instead, I fastened a hacksaw blade to the edge of my workbench. I slipped a washer behind the blade at each of the mounting holes so a sheet of sandpaper to easily slides in behind the blade. I fold the paper where I want to cut, just as a reference. — Kim Boley. Try some of these storage solutions!
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips. 

While many woods can be used for carving, there are some clear favorites, including Aspen, Basswood, Butternut, Black Walnut, and Oak.[14] Because it has almost no grain and is notably soft, Basswood is particularly popular with beginner carvers. It is used in many lower-cost instruments like guitars and electric basses.[14] Aspen is similarly soft, although slightly harder, and readily available and inexpensive.[14] Butternut has a deeper hue than Basswood and Aspen and has a nice grain that is easy to carve, and thus friendly for beginners. It's also suitable for furniture.[14] While more expensive that Basswood, Aspen, and Butternut, Black Walnut is a popular choice for its rich color and grain.[14] Lastly, Oak is a strong, sturdy, and versatile wood for carving with a defined grain. It's also a popular wood for furniture making.[14]
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!

Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
A bottle carrier is a bucket like carrier used to carry beer bottles and so. Yes, the same one you must have used to carry your six-pack. Drinker or not, a bottle carrier is a useful item for everyone. It can be used to carry around or store small items around a household. And it is also very easy to build one. I have several of these lying around my house. Also known as wooden beer totes, this is one wood item you will absolutely love to make. It is also super easy to build.
Typically furniture such as tables and chairs is made using solid stock from hardwoods due to its strength and resistance to warping.[10] Additionally, they also have a greater variety of grain patterns and color and take a finish better which allows the woodworker to exercise a great deal of artistic liberty. Hardwoods can be cut more cleanly and leave less residue on sawblades and other woodworking tools.[10] Cabinet/fixture makers employ the use of plywood and other man made panel products. Some furniture, such as the Windsor chair involve green woodworking, shaping with wood while it contains its natural moisture prior to drying.

Typically furniture such as tables and chairs is made using solid stock from hardwoods due to its strength and resistance to warping.[10] Additionally, they also have a greater variety of grain patterns and color and take a finish better which allows the woodworker to exercise a great deal of artistic liberty. Hardwoods can be cut more cleanly and leave less residue on sawblades and other woodworking tools.[10] Cabinet/fixture makers employ the use of plywood and other man made panel products. Some furniture, such as the Windsor chair involve green woodworking, shaping with wood while it contains its natural moisture prior to drying.


Here’s a safe and sound way to make long cuts with a circular saw on plywood clamped to a worktable. Cut about 12 in. into the plywood, then twist a piece of duct tape into a bow tie, with up-and-down adhesive faces. Slide it in the saw kerf and press the tape down above and under the plywood. Now as you finish the cut, the trailing end can’t curl down dangerously as you saw. Hats off to Mike Connelly for simplifying this job. Check out how to make this DIY duct tape wallet.
Examples of Bronze Age wood-carving include tree trunks worked into coffins from northern Germany and Denmark and wooden folding-chairs. The site of Fellbach-Schmieden in Germany has provided fine examples of wooden animal statues from the Iron Age. Wooden idols from the La Tène period are known from a sanctuary at the source of the Seine in France.
The video explains the step by step process of making a nice wooden phone stand from scratch. My first wooden holder was not the best one, but it was good enough to motivate me to make more. I now possess 10 mobile wooden stands in different shapes and styles. And if I can make this, you too can make one yourself. Search the internet for more mobile holder ideas and start making one now.
Afrormosia Alder Andiroba Anigre Ash Apple Aspen Avodire Balsa Beech Bilinga Birch African Blackwood Australian Blackwood Boxwood Bubinga Camphor Cedrela Cherry Chestnut Cocobolo Cumaru Ebony Elm Eucalyptus Hazel Hickory Hornbeam Idigbo Imbuia Ipê Iroko Jarra Jelutong Lignum vitae Linden (lime, basswood) Merbau Mahogany (American, African) Maple Meranti Oak Padauk Pear Plum Poplar Purpleheart Ovankol Ramin Red Quebracho Rosewood Rubberwood Sapele Teak Totara Utile Walnut Wenge Willow Zebrano
Check out our new Brazos Net Rips! With new, state-of-the-art equipment we can rip lumber to your finished width with ultimate precision and accuracy using glue-line rip blades. Our saw can even rip parallel edges of random width boards using laser guided technology to ensure the highest yield possible out of each and every board. Start getting the most out of your lumber, contact your local Brazos sales representative today for more information!

From the image above it seems that you do not require a big tutorial to help you to build this candle holder. All you need is a wood panel, a hook and some nails/screws and do exactly what you see in the picture. Attach the hook to the wood panel using two screws and then, attach the panel to the wall using more nails or screws. That’s it. I hope this gets the job done.
Clamping up four mitered corners is tricky. You can buy specialty clamps for this, but I make my own. Here’s how to do it. Start with a long 1×4, as it’s easier (and safer) to clamp for making the angled cuts than a short piece. Mark out the blocks, and then drill a 1-in. diameter hole in the center of each one. The hole prevents the blocks from getting glued to your project. Cut 45-degree angles tangent to the hole, and then cut the blocks free from the long board. We’ll walk you through how to make one for your home shop.
“I do a lot of finish-sanding freehand, without a sandpaper block, so I can smooth edges and get into nooks and crannies. But the finer grits are usually bonded to thinner paper and, at least for me, the paper is too thin and ends up tearing long before the grit wears out. So I apply duct tape to the back of the sandpaper. The sandpaper is still flexible enough to sand a tight radius and it’s far more durable. You can use this super-strong sandpaper like a shoeshine rag.” — Chuck Merchant
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
Second, learning how to read lumber dimensions, like knowing what 1×2 or 2×12 actually means, is really important. Understanding softwood lumber dimensions will help you to read woodworking build plans, shop for lumber, and understand the general measurements for your projects. I’ve provided a simple explanation to lumber sizes along with a free lumber size chart printable here!
$50 - $100Alaska Dream HouseBathroomBedroomChildren's and Kid's Room Furniture and Toy PlansCraftroomDesk, Desk Systems and Project Table Plansdining roomentry wayFarmhouse Style Furniture PlansIndustrial Style Furniture PlansKids and Toysliving roomModern Style Furniture PlansNursery and BabyofficeRustic Furniture Plansstorage and organizationTeensIntermediateSide and End Table PlansBuffet, Sideboard and Credenza PlansCabinet PlansNightstands
This is one of those things that you never know you need unless you have one. This amazing wooden sofa sleeve works perfectly on either or both sides of a sofa set. It gives your sofa a nice look. The sleeve can also be modified to include a cup holder, mobile holder, etc. You can easily find this item on any online furniture store, but an even better idea is to build one. This way, you can make a sofa sleeve design that you actually like and make space for cup and other things.
How do you divide 11-3/8-in. (or any other mathematically difficult number) into equal parts without dividing fractions? Simple. Angle your tape across the workpiece until it reads an easily-divisible dimension and make your marks with the tape angled. For example, say you want to divide an 11-3/8-in. board into three equal parts. Angle the tape until it reads 12-in., and then make marks at “4” and “8”. Plus: More measuring tips and tricks.

Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.
To corral shelf-dwelling books or DVDs that like to wander, cut 3/4-in.-thick hardwood pieces into 6-in. x 6-in. squares. Use a band saw or jigsaw to cut a slot along one edge (with the grain) that’s a smidgen wider than the shelf thickness. Stop the notch 3/4 in. from the other edge. Finish the bookend and slide it on the shelf. Want to build the shelves, too? We’ve got complete plans for great-looking shelves here.
The shelf in the first picture is made of red oak plywood. You can choose the wood type, color and design as you like for your project. In case if you need more help understanding this project, you can refer the source link below. It discusses various items used, steps and tips and personal experience of the author who personally built a Zigzag shelf.
I’m 91 years old, but I still enjoy spending time in the wood shop. I like to make wooden toys and give them to my great-grandkids and charity groups. One trick I’ve learned over the years is to use emery boards—the kind for filing fingernails— to sand small parts. Emery boards come in different sizes, and some are more abrasive than others, so I keep an assortment on hand. — Joe Aboussleman
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.
This is probably one the easiest woodworking projects you will find here. Although easy, a doormat is an equally important and useful item for households. As you can see in the image below, you will only need some 2X2 wooden boards and rope to build a simple doormat. This doormat is mostly useful for outdoor and porch. It will easily remove all the mud from your shoes with just one wipe. It is also very easy to clean and looks fabulous even if it is dirty.
Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.
Sanding small items is tricky, as they’re hard to clamp in a vise to work on them. So instead of bringing the sandpaper to the workpiece, I bring the workpiece to the sandpaper. I glue sheets of sandpaper to a piece of plywood; 60 and 100-grit on one side and 150 and 220-grit on the other. Spray adhesive works well for this. Since there’s sandpaper on both sides, my sanding board doesn’t slide around on the bench. Check out these small projects!

Not long ago, I needed to make some angled wood parts to build a new soffit on my garage. I didn’t have the customary tool for the job, but I had some steel joining plates. I screwed through one of the holes in the plate, set my angle, then added another screw to lock the angle. I could then use it as a template to mark all the pieces at the same angle and cut them with my circular saw. — Ryan Bartsch
Sanding the inside of a hole or curved surface can be difficult. To simplify that task, insert a 1/4 x 3-in. bolt into the pilot hole of a hole-saw cutout. Secure the bolt with a washer and nut. Using a hacksaw, cut a 1/4-in. deep slot in line with the bolt. Cut a piece of adhesive-backed sandpaper so that you can slide one end into the slot, wrap it around the cutout, and slide the other end back into the slot. Chuck the bolt into a drill, and you now have a homemade drum sander. — E.R. Comstock. How to Sand Wood Faster
Old doors laid across sawhorses make great temporary workbenches, but they take up a lot of space when you’re not using them. Instead of full-size doors, I use bifold doors with hinges so I can fold them up when I’m done working. They’re also easier to haul around in the pickup for on-the-road jobs. — Harry Steele. Here are 12 more simple workbenches you can build.
Second, learning how to read lumber dimensions, like knowing what 1×2 or 2×12 actually means, is really important. Understanding softwood lumber dimensions will help you to read woodworking build plans, shop for lumber, and understand the general measurements for your projects. I’ve provided a simple explanation to lumber sizes along with a free lumber size chart printable here!
×