Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.
From the source tutorial, you can get illustrates to the instruction about the plan. Everything is fairly described as diagrams, images, the list of supplies and tools need etc. The process to this plan is very easy to understand and follow for if you are having some basic woodworking knowledge. Make sure to collect all the supplies you need before you start with the project. You may even ask any question directly in the comment section of the tutorial post and also comment the images of your final product if you have completed it. Either way, I hope that you will manage to build this one nicely.​
Softwood is most commonly found in the regions of the world with lower temperatures and is typically less durable, lighter in weight, and more vulnerable to pests and fungal attacks in comparison to hardwoods. They typically have a paler color and a more open grain than hardwoods, which contributes to the tendency of felled softwood to shrink and swell as it dries.[9] Softwoods usually have a lower density, around 25-37lb/cu ft, which can compromise its strength.[9] Density, however, does vary within both softwoods and hardwoods depending on the wood's geographical origin and growth rate. However, the lower density of softwoods also allows it to have a greater strength with lighter weight. In the United States, softwoods are typically cheaper and more readily available and accessible.[9] Most softwoods are suitable for general construction, especially framing, trim, and finish work, and carcassing.[10][9] 

The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.
Sanding small items is tricky, as they’re hard to clamp in a vise to work on them. So instead of bringing the sandpaper to the workpiece, I bring the workpiece to the sandpaper. I glue sheets of sandpaper to a piece of plywood; 60 and 100-grit on one side and 150 and 220-grit on the other. Spray adhesive works well for this. Since there’s sandpaper on both sides, my sanding board doesn’t slide around on the bench. Check out these small projects!
This was not actually a tutorial post to the woodworking plan ideas but the aim of the post was to give some easy and free woodworking ideas to the readers. If you have some time to entertain yourself and also willing to add some new stuff to your furniture you can take any idea from the list and start working on it. Be sure to see both post tutorial and video tutorials of the plan you have selected, it will make you understand everything nicely.
See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products
​The plan tutorial includes images, diagrams, step-by-step instructions, and even a video to help you along the way. You can also go with some more bookcase design ideas. Browse the internet for more and we are also proving a link below to some more ideas to this plan. Select and build one of these free bookcase DIYs and you will have everything available easily that you need to get started creating a bookshelf for any room in your house.
Along with stone, clay and animal parts, wood was one of the first materials worked by early humans. Microwear analysis of the Mousterian stone tools used by the Neanderthals show that many were used to work wood. The development of civilization was closely tied to the development of increasingly greater degrees of skill in working these materials.
Hi Liz. I am sorry you were having trouble unsubscribing to the newsletter. Your information has been updated. Your email address has been removed from our Woodworkers Guild of America E-Newsletter mailing list. Please allow up to 5 business days for your request to be completed. If you have any questions, please contact our customer service team at 1-855-253-0822.
Softwood is most commonly found in the regions of the world with lower temperatures and is typically less durable, lighter in weight, and more vulnerable to pests and fungal attacks in comparison to hardwoods. They typically have a paler color and a more open grain than hardwoods, which contributes to the tendency of felled softwood to shrink and swell as it dries.[9] Softwoods usually have a lower density, around 25-37lb/cu ft, which can compromise its strength.[9] Density, however, does vary within both softwoods and hardwoods depending on the wood's geographical origin and growth rate. However, the lower density of softwoods also allows it to have a greater strength with lighter weight. In the United States, softwoods are typically cheaper and more readily available and accessible.[9] Most softwoods are suitable for general construction, especially framing, trim, and finish work, and carcassing.[10][9]

With the advances in modern technology and the demands of industry, woodwork as a field has changed. The development of Computer Numeric Controlled (CNC) Machines, for example, has made us able to mass-produce and reproduce products faster, with less waste, and often more complex in design than ever before. CNC Routers can carve complicated and highly detailed shapes into flat stock, to create signs or art. Rechargeable power tools speed up creation of many projects and require much less body strength than in the past, for example when boring multiple holes. Skilled fine woodworking, however, remains a craft pursued by many. There remains demand for hand crafted work such as furniture and arts, however with rate and cost of production, the cost for consumers is much higher.


We will suggest you select the simple Birdhouse if you are new at woodworking but be sure to select its design with respect to the place where you are going to hang/place it. One of our simple Birdhouse tutorials will help you building one. We have managed to include a source tutorial below that will help you to understand illustrates and the instruction to building a simple Birdhouse.
A while back, I reached for my two containers of epoxy and noticed that the resin in one container had crystallized exactly like honey that’s been in the cupboard too long. The solution is exactly the same too: Set the container in a bowl of hot tap water. After about 15 minutes, I emptied the container and refilled it with hot water. After about a half hour, the epoxy regained its normal consistency. Good as new! — Ken Holte

Harbor Freight carries a wide range of high quality woodworking tools that are perfect for the home garage and professional carpentry shop alike. If you have a love of woodcrafting, Harbor Freight has the essential tools and accessories you need to tackle woodworking projects efficiently and safely, no matter your skill level. Our huge selection of drill presses, saws, sanders and planers will see you through countless jobs while our dust collection options keep your workspace clear of sawdust. Whatever you’re looking for, from basic woodworking tools to more specialty items, Harbor Freight has what you need to get the job done.


This is another example of small woodwork projects that require good time and woodworking skills. This item is built using multiple wooden parts. Each part is shaped in a specific design and then all parts are attached together to make the final TV set. I have never tried building this one, mostly because I don’t own an iPhone, but also because making this item is not an easy task. By the way, it works fine with all kinds of phones.
It might not be the easiest project in this list, but if you already have some experience with wood cutting and joinery, it won’t be any hassle at all. Thanks to the extremely detailed instructions it shouldn’t really be a problem even if you’re not very familiar with woodworking. This could actually be a great project for refining your woodworking skills as a beginner!
To corral shelf-dwelling books or DVDs that like to wander, cut 3/4-in.-thick hardwood pieces into 6-in. x 6-in. squares. Use a band saw or jigsaw to cut a slot along one edge (with the grain) that’s a smidgen wider than the shelf thickness. Stop the notch 3/4 in. from the other edge. Finish the bookend and slide it on the shelf. Want to build the shelves, too? We’ve got complete plans for great-looking shelves here.
Relax and enjoy your outdoor space with this smart patio combo consisting of a sofa and chair. You can adjust the size completely to make it fit perfectly onto your patio or deck, and both the sofa and chair have arms that double as trays for al fresco dining. And you can make your own cushions to fit, or use shop-bought ones and add your own ties, if necessary.
This self-clamping table saw fence takes only seconds to put on and lets you crank the blade into the fence to create both angled cuts along board edges and extremely thin rip or rabbet cuts. With a hand- or jigsaw, cut pieces from a 1×4, making the inside width of the “L” a hair under the thickness of your saw’s fence. Drill 5/16-in. holes in the L-blocks and plywood fence and join them with two 1/4-in. x 3-in. countersunk machine screws, washers and Wing-Nuts. As always, use extra caution when you’re sawing without a blade guard. Our thanks for this new sawing angle to professional furniture maker George Vondriska. Check out these 16 genius tool hacks you need to know!
Making an art or a design on a wooden piece is a hectic task and requires good art skills. But there is another much easier way to carve a beautiful art on any wood surface. For this, you will need the image or graphic that you want to transfer, a piece of wood, freezer paper, etc. I, myself have made several such designs. At the source below, you can find a step by step guide for transferring a graphic image to the wood.
Short scraps of hardwood are too good to throw away but hard to store neatly. So I bought a 4-ft. tube form made for concrete footings, cut it in half (the cardboard-like material cuts easily) and set the tubes on end. I tack the tubes to a wall or a bench leg so they don’t fall over. With the wood scraps stored upright, it’s easy to find a piece just the right length. Tube forms are available in various diameters for $5 and up at home centers. — Bill Wells. Here’s another brilliant use for these concrete forms.
This was not actually a tutorial post to the woodworking plan ideas but the aim of the post was to give some easy and free woodworking ideas to the readers. If you have some time to entertain yourself and also willing to add some new stuff to your furniture you can take any idea from the list and start working on it. Be sure to see both post tutorial and video tutorials of the plan you have selected, it will make you understand everything nicely. 

As you can see in the image, this shelf goes on both sides of the corner wall. It looks beautiful and can be used to organize books, trophies, pictures frames and many other things. The strength and design of the shelf depends on how properly you build it. First time workers definitely need some guidance to help them with the process. Therefore, I am including this basic video that I found on YouTube that demonstrates the process of making corner wall wooden shelves.
Woodworking was essential to the Romans. It provided, sometimes the only, material for buildings, transportation, tools, and household items. Wood also provided pipes, dye, waterproofing materials, and energy for heat.[5]:1Although most examples of Roman woodworking have been lost,[5]:2 the literary record preserved much of the contemporary knowledge. Vitruvius dedicates an entire chapter of his De architectura to timber, preserving many details.[6] Pliny, while not a botanist, dedicated six books of his Natural History to trees and woody plants, providing a wealth of information on trees and their uses.[7]
I got this idea from a Pinterest post. The final product looks so beautiful that I just couldn’t wait to make one for myself. This was somewhat a different experience from my other regular DIY projects as it doesn’t involve making something from scratch, but turning an existing wood piece into another one. Nonetheless, I enjoyed it very much and the final product was very satisfying. The tutorial I used is linked below.
Turning an old door into a photo frame is another easy woodwork project. All you need is an old door and some woodworking tools and items. I am here sharing the link to the source tutorial that explains the step by step procedure for building a picture frame from an old wooden door. This tutorial was originally written by Tracy Snyder at athomewithsweett.blogspot.com who also tells you what items you may need and where to find them. If you haven’t already got an old door, you can purchase one from websites like Craigslist.

Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.


This is probably one the easiest woodworking projects you will find here. Although easy, a doormat is an equally important and useful item for households. As you can see in the image below, you will only need some 2X2 wooden boards and rope to build a simple doormat. This doormat is mostly useful for outdoor and porch. It will easily remove all the mud from your shoes with just one wipe. It is also very easy to clean and looks fabulous even if it is dirty.
For many of us, the moment we learned that a 2×4 board is actually 1.5 inches x 3.5 inches was simply mind-blowing. The reason for this apparent contradiction is that the board has been planed down to eliminate irregularities. At one point, many years ago, 2x4s actually were 2 inches x 4 inches, but their rough surfaces made them difficult to stock and handle. The old terms, such as 2×4 or 4×4, are still used, and are known as the “nominal” size of the board. These nominal sizes are used because they are easier to say and they stick to tradition. Now, thanks to a lawsuit, most big box stores list the nominal and actual sizes of lumber.

Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.
As soon as I came across this tutorial, I didn’t wait any longer to start building one. Some of the items you need for this project are hardwood plywood, saw, glue, nails, drilling machine, etc. The video is very easy to follow for anyone with basic woodworking knowledge and experience. The first source link also includes a step by step procedure in plain English for those, who are not comfortable enough with the video tutorial.
I am sharing here a link to the detailed tutorial written by Pete at diypete.com, who shares the step by step process for making a wonderful barrel coffee table from scratch. He also tells you what items you’ll need for this project and where to find them. For example, you can buy an old whiskey barrel online or from a local whiskey store for a few bucks, if you haven’t already got one.
Making a garden arched footbridge out of some wood boards can be fun, hard working plan and also it’s quite rewarding. We are providing the project tutorial for how to build an arched footbridge without rails or having rails. If you take your hands of work and have some basic woodworking skills you can easily build this type of bridge. While this garden bridge is too small to walk over but it can make a really stunning addition to your lush yard or garden.
A bottle carrier is a bucket like carrier used to carry beer bottles and so. Yes, the same one you must have used to carry your six-pack. Drinker or not, a bottle carrier is a useful item for everyone. It can be used to carry around or store small items around a household. And it is also very easy to build one. I have several of these lying around my house. Also known as wooden beer totes, this is one wood item you will absolutely love to make. It is also super easy to build.
Another awesome thing about this coffee table is that it is also has a storage unit. So you can store drinks, and other stuff in the half barrel of your table and then close or open it whenever you need. Pete has also constructed a video for this tutorial for which you can find the link below. It illustrates the same process in a video guide that shows you the exact process to be followed while building this whiskey barrel coffee table.

This is one of those things that you never know you need unless you have one. This amazing wooden sofa sleeve works perfectly on either or both sides of a sofa set. It gives your sofa a nice look. The sleeve can also be modified to include a cup holder, mobile holder, etc. You can easily find this item on any online furniture store, but an even better idea is to build one. This way, you can make a sofa sleeve design that you actually like and make space for cup and other things.
Founded in 1977, Harbor Freight Tools is the leading discount tool retailer in the U.S. selling great quality tools at "ridiculously low prices" in our 1000+ stores nationwide and on its website www.harborfreight.com. Harbor Freight Tools stocks over 7,000 items in categories including automotive, air and power tools, shop equipment and hand tools. With a commitment to quality and a lifetime guarantee on all hand tools, Harbor Freight Tools is a favorite of automotive and truck repair shops, government agencies, schools, manufacturers, contractors and tool enthusiasts who want top-quality and great selection and value. The results speak for themselves - with over 40 million customers and thousands of people switching to Harbor Freight Tools every day.
Copyright 2018 by Cut The Wood. CutTheWood.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, CutTheWood.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.
Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.
For your kitchen, it can work as a knife rack. It gives you easy access to all essential tools while saving space. In addition, it adds a nice visual appeal to your kitchen wall. You can customize your wall rack with different materials, designs and styles. I am here sharing the source link to the step by step tutorial about how to make a rustic wall knife rack.
A board is considered “quarter-sawn” when the growth rings run, more or less, perpendicular to the face of the board. Quarter-sawn boards generally have straight grain and are less prone to shrinkage, compared to other boards. These factors don’t come into play with the 2x4s you use to frame a closet—but it does with the shelves and cabinetry you put into that closet; you want those boards to remain straight, flat and stable.

The shelf in the first picture is made of red oak plywood. You can choose the wood type, color and design as you like for your project. In case if you need more help understanding this project, you can refer the source link below. It discusses various items used, steps and tips and personal experience of the author who personally built a Zigzag shelf.


My planer blasts shavings all over the shop floor. I decided to make my own dust chute from 4-in. PVC sewer pipe (which has thinner walls than regular Schedule 40 pipe) and a couple caps. I cut a slit in the pipe and used a heat gun to soften the plastic. That allowed me to open the slit. (Heating PVC releases fumes; ventilation is critical.) I then drilled holes in the flap and screwed it to the planer housing. Finally, I cut a 2-1/2- in. hole in one of the end caps to accept my shop vacuum hose. Works great! — Luis Arce. Here’s what else you can do with PVC pipe.

We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it!
Sanding curves is tricky. Sometimes you need a sanding pad that’s both firm and flexible. A small notepad works great. Just wrap sandpaper around the pad and bend the pad to whatever arc you need. Slip the one end of the sandpaper between the pages to help hold it in place on the pad. Give this a try the next time you’re working on a project that has curves and tough to reach spots.
Clamping up four mitered corners is tricky. You can buy specialty clamps for this, but I make my own. Here’s how to do it. Start with a long 1×4, as it’s easier (and safer) to clamp for making the angled cuts than a short piece. Mark out the blocks, and then drill a 1-in. diameter hole in the center of each one. The hole prevents the blocks from getting glued to your project. Cut 45-degree angles tangent to the hole, and then cut the blocks free from the long board. We’ll walk you through how to make one for your home shop.

You can transfer a graphic on any wood piece of your choice, including a frame, top of a table, etc. The surface should be clean and big enough for the graphic paper. I am also sharing a video tutorial here that explains in detail the process of transferring any graphic to a wooden surface using a freezer paper. Just gather the items you need and follow this video to carve your favorite designs on your favorite wood items.
​The plan tutorial includes images, diagrams, step-by-step instructions, and even a video to help you along the way. You can also go with some more bookcase design ideas. Browse the internet for more and we are also proving a link below to some more ideas to this plan. Select and build one of these free bookcase DIYs and you will have everything available easily that you need to get started creating a bookshelf for any room in your house.
KHIEM NGUYEN (Age 28, Austin, TX): Inspired by midcentury modern and Japanese design, Nguyen is a true craftsman. His passion for crafting began with photography and led to him becoming an open major in art school so he could "get (his) hands into everything." After college, Nguyen and his fiancée moved to Austin, where they began A & K Woodworking & Design, specializing in furniture and wood crafts.
A small oak table is a very useful wooden item for every household. You can yourself make a nice, strong and beautiful oak table suitable for any purpose. See the image below. As you can see, it is a small, yet good enough table to be used as a coffee table, lamp stand, breakfast table, etc. You can also find many other design variants on the internet. Choose the one you want for yourself and start making it now.
Examples of Bronze Age wood-carving include tree trunks worked into coffins from northern Germany and Denmark and wooden folding-chairs. The site of Fellbach-Schmieden in Germany has provided fine examples of wooden animal statues from the Iron Age. Wooden idols from the La Tène period are known from a sanctuary at the source of the Seine in France.
This simple jig makes laying out circles a breeze. Drill a 1/8-in. hole through every inch mark on a ruler or yard-stick. To draw a circle, place a pin through the number “1” into the center of your board. Add 1 in. to the radius of the circle you wish to draw, and insert a pencil into this number. Using the pin as a pivot, rotate the pencil to mark the circle. — Edwin Constantino. How to Cut Curves in Wood
Woodworking was essential to the Romans. It provided, sometimes the only, material for buildings, transportation, tools, and household items. Wood also provided pipes, dye, waterproofing materials, and energy for heat.[5]:1Although most examples of Roman woodworking have been lost,[5]:2 the literary record preserved much of the contemporary knowledge. Vitruvius dedicates an entire chapter of his De architectura to timber, preserving many details.[6] Pliny, while not a botanist, dedicated six books of his Natural History to trees and woody plants, providing a wealth of information on trees and their uses.[7]
Pocket screw joinery is a system—employing special drill and driver bits—used to join boards or pieces of plywood to one another. Installing pocket screws involves using a jig to drill a sharply angled, 15-degree hole through the back of one board, then driving a special screw through that hole into the second board to draw them tightly together. Learn how to use pocket screws here. It’s often used in cabinetmaking and furniture building. Here’s how to build cabinets with pocket screws. The term “pocket” comes from the design of the hole which contains an upper “pocket” for the head of the screw to push against; this pocket also hides the head of the screw.

Another important factor to be considered is the durability of the wood, especially in regards to moisture. If the finished project will be exposed to moisture (e.g. outdoor projects) or high humidity or condensation (e.g. in kitchens or bathrooms), then the wood needs to be especially durable in order to prevent rot. Because of their oily qualities, many tropical hardwoods such as teak and mahogany are popular for such applications.[9] 

Particleboard is a manufactured wood product composed of sawdust, wood chips or wood shavings mixed with a resin. This concoction is layered, compressed, subjected to heat and cut to shape, resulting in a sheet material that can be used for a variety of things. It’s often used as shelving or as an underlayment for carpet. Plastic laminate may be applied to both sides to create a product that can be used to create everything from furniture to cabinets to wall paneling. Head into IKEA and you’ll find acres of particleboard.
The tutorial that I am sharing here was written by someone who built this pallet art just to improve the value of a property they wanted to sell fast and they succeed in it. So you can imagine how wonderful this item must look like. I am assuming you do not just want to make this beautiful pallet art so that you can also sell your property easily. Well, whatever your reasons are, this beauty is able to attract anyone who visits your house.
See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products
Having swing in your own home, yard or garden can be so de-stressing and be relaxing a thing to enjoy, that doesn’t matter you have a big yard or patio, or vacant porch. Kids will surely fall in love with this swing porch and love playing on a breezy day. Even, adults also do relax and enjoy a quite morning coffee, or just being embraced by the sun in the swing.
The rubber cushion on my old palm sander was wearing thin around the edges. Because of its age, I couldn’t find a replacement pad. As I was drinking my beverage with a foam can cover around it, I realized I could cut the foam to fit the sander and glue it on. I peeled off the old pad, cleaned the metal base and attached the foam with contact cement. Works for clamp-on as well as stick-on sanding squares! You can find can covers at discount and convenience stores. — Allen J. Muldoon
×