With an orbital sander and good sandpaper you can smooth wood evenly and easily with first-class results. When flush-sanding solid edge-banding, draw a squiggly line across the joint before sanding. The edge-banding will be slightly proud of the plywood veneer, so the pencil marks provide a visual aid to make sure that you’re sanding flat, and that you don’t sand through the plywood’s veneer. As you go, you can also test for a smooth, level transition by gently scraping your fingernails against the transition. If it’s smooth, your fingers will not catch on the seam between the two pieces
Softwood is most commonly found in the regions of the world with lower temperatures and is typically less durable, lighter in weight, and more vulnerable to pests and fungal attacks in comparison to hardwoods. They typically have a paler color and a more open grain than hardwoods, which contributes to the tendency of felled softwood to shrink and swell as it dries.[9] Softwoods usually have a lower density, around 25-37lb/cu ft, which can compromise its strength.[9] Density, however, does vary within both softwoods and hardwoods depending on the wood's geographical origin and growth rate. However, the lower density of softwoods also allows it to have a greater strength with lighter weight. In the United States, softwoods are typically cheaper and more readily available and accessible.[9] Most softwoods are suitable for general construction, especially framing, trim, and finish work, and carcassing.[10][9]
Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.
With two varieties, red and white, oak is known to be easy to work with and relatively strong. However, furniture makers often opt for white oak over red oak for its attractive figure and moisture-resistance.[12] Depending on the kind needed, oak can probably be found at a local home center or a lumberyard for a bit pricier than other hardwoods.[12][13]
While trying to trace an exact copy of the throat plate for my table saw, I came up with this nifty technique using an ordinary pencil. I just shaved my pencil into a half-pencil by carefully grinding it on my belt sander. The flat edge enables my modified pencil to ride straight up along the edge of the template. It also works great for marking and then shaping inlays for my woodworking projects. — Tim Reese. How to cut circles with a band saw.

The rubber cushion on my old palm sander was wearing thin around the edges. Because of its age, I couldn’t find a replacement pad. As I was drinking my beverage with a foam can cover around it, I realized I could cut the foam to fit the sander and glue it on. I peeled off the old pad, cleaned the metal base and attached the foam with contact cement. Works for clamp-on as well as stick-on sanding squares! You can find can covers at discount and convenience stores. — Allen J. Muldoon
While many woods can be used for carving, there are some clear favorites, including Aspen, Basswood, Butternut, Black Walnut, and Oak.[14] Because it has almost no grain and is notably soft, Basswood is particularly popular with beginner carvers. It is used in many lower-cost instruments like guitars and electric basses.[14] Aspen is similarly soft, although slightly harder, and readily available and inexpensive.[14] Butternut has a deeper hue than Basswood and Aspen and has a nice grain that is easy to carve, and thus friendly for beginners. It's also suitable for furniture.[14] While more expensive that Basswood, Aspen, and Butternut, Black Walnut is a popular choice for its rich color and grain.[14] Lastly, Oak is a strong, sturdy, and versatile wood for carving with a defined grain. It's also a popular wood for furniture making.[14]
Cutting sandpaper is a quick way to dull your scissors or utility knife blade. Instead, I fastened a hacksaw blade to the edge of my workbench. I slipped a washer behind the blade at each of the mounting holes so a sheet of sandpaper to easily slides in behind the blade. I fold the paper where I want to cut, just as a reference. — Kim Boley. Try some of these storage solutions!

I use binder clips for a lot of things around the shop, and here’s one that I thought I’d share. When I need to make multiple cuts all the same length, I just clamp my jumbo binder clip to my fence and use a 1/4-in.-thick wood scrap pinched in the clip as a stop. Works like a charm! When it’s not in use, I clamp it to the cord so it’s always nearby. — John Muchow
Always nice to see project ideas. Yet, to make a living while woodworking all projects need to be scaled up so that one can actually earn enough to survive and compete against the flood of Chinese imports and others. Substitute products made from plastic, metal or wood are a common place and normally cheaper due to mass production and human rights violations. Politicians don’t care about the disappearance of many of America’s Cottage Industries and most consumers don’t care as well.
To corral shelf-dwelling books or DVDs that like to wander, cut 3/4-in.-thick hardwood pieces into 6-in. x 6-in. squares. Use a band saw or jigsaw to cut a slot along one edge (with the grain) that’s a smidgen wider than the shelf thickness. Stop the notch 3/4 in. from the other edge. Finish the bookend and slide it on the shelf. Want to build the shelves, too? We’ve got complete plans for great-looking shelves here.
Clamping up four mitered corners is tricky. You can buy specialty clamps for this, but I make my own. Here’s how to do it. Start with a long 1×4, as it’s easier (and safer) to clamp for making the angled cuts than a short piece. Mark out the blocks, and then drill a 1-in. diameter hole in the center of each one. The hole prevents the blocks from getting glued to your project. Cut 45-degree angles tangent to the hole, and then cut the blocks free from the long board. We’ll walk you through how to make one for your home shop.

Instead of using a container to mix a small amount of epoxy, just make a mixing surface on your workbench using painters tape. Simply lay down strips, overlapping the edges so the epoxy doesn’t get on your bench. When you’re done, peel off the tape and throw it away. This mixing surface will work for more than just epoxy, you can use it for wood glue or any other material you need easy access to while working on a project.
Here’s an easier way to stain or seal chairs, lattice or anything with numerous tight recesses. Pour the stain into a clean, empty spray bottle ($3). Spray the stain onto the project and wipe up the excess with a brush or rag. The sprayer will squirt stain into all those tight, hard-to-reach cracks and joints. — Valrie Schuster. Learn more about staining wood.
Finding a toolbox for a mechanic, for his hand tools, is not a big challenge at all - there are dozens of the tool boxes available on the market, from huge roll-around shop cases to small metal boxes. Plumbers, electricians, and farmers are well served, too, with everything from pickup-truck storage to toolboxes and belts. But, if you are a shop-bound woodworker then the case changes. You get to need a tool box that suits the range and variety of hand tools that most woodworkers like to have. For those who deny making do with second best, there's only one solution, you’ve to build a wooden toolbox that should be designed expressly for a woodworking shop.
Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.

The items you’ll need for this project include wood board, power drill, tape measure, adhesive, etc. Read the tutorial for details. Follow the steps properly to make a nice and strong wall rack. This rack makes use of magnets to hold metal items. The tutorial explains the procedure for building this beautiful wall rack. Make sure to use only high quality items for any woodworking project. Use the rack only to hang items that are not too heavy for the magnet to hold. Also, be careful while working around this wall rack and beware of the knives falling off the rack.
Cutting a miter joint that closes up perfectly and maintains a 90 degree angle is really satisfying. Unfortunately, it doesn’t always happen. Here’s a quick fix for a slightly open miter joint; rub the shank of a screwdriver along the miter at a steep angle, from both sides of the joint. Chances are, you’ll be the only one that knows it wasn’t perfect to begin with! Try this amazing miter project!
Brazos Forest Products is the premier distributor of quality hardwood, plywood, and custom moulding in Texas and Louisiana. Our manufacturing locations can produce high quality custom mouldings to your specifications. Our three locations in Texas – Austin, Dallas/Ft. Worth, Houston, and our fourth location in Denham Springs, Louisiana enable us to serve all your hardwood needs.
Clamping mitered edges can be a real hassle because they never seems to line up correctly. The easiest way that I’ve found to get around this process is to use painter’s tape as clamps. First set the pieces so that the outer edges are facing up and tape them edge-to-edge. The flip the pieces over so the beveled edges are facing up and glue them together. Complete the process by taping the last two edges together and let sit until completed. The tape removes easily and the glue won’t attach to the tape, making sanding and finishing very simple. Try this tip with this clever project!
Boat building Bow and arrow Bush carpentry Cabinetry Caning Carpentry Certosina Chainsaw carving Chip carving Clogs Ébéniste Fretwork Intarsia Japanese carpentry Khatam Kohlrosing Log building Marquetry Millwork Parquetry Pyrography Relief carving Root carving Sawdust Segmented turning Shingle weaving Shipbuilding Spindle turning Timber framing Treen Whittling Wood carving Woodturning Wood flour
The progenitors of Chinese woodworking are considered to be Lu Ban (魯班) and his wife Lady Yun, from the Spring and Autumn period (771 to 476 BC). Lu Ban is said to have introduced the plane, chalk-line, and other tools to China. His teachings were supposedly left behind in the book Lu Ban Jing (魯班經, "Manuscript of Lu Ban"). Despite this, it is believed that the text was written some 1500 years after his death. This book is filled largely with descriptions of dimensions for use in building various items such as flower pots, tables, altars, etc., and also contains extensive instructions concerning Feng Shui. It mentions almost nothing of the intricate glue-less and nail-less joinery for which Chinese furniture was so famous.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
These things may be tiny in size, but building one is not that easy. It takes some serious woodworking knowledge and skill to build a nice wooden mobile stand. When I first saw one online, I just couldn’t resist thinking of buying one. But when I saw the price, I was forced to rethink. Also, a woodwork lover like me cannot be contained with just one piece and I was not willing to spend on more than one. So instead I decided to build myself one. Yes, it took some doing but the final result was satisfying. Luckily, I found this awesome tutorial online that helped me build my first ever wooden phone holder.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
It might not be the easiest project in this list, but if you already have some experience with wood cutting and joinery, it won’t be any hassle at all. Thanks to the extremely detailed instructions it shouldn’t really be a problem even if you’re not very familiar with woodworking. This could actually be a great project for refining your woodworking skills as a beginner!
I use binder clips for a lot of things around the shop, and here’s one that I thought I’d share. When I need to make multiple cuts all the same length, I just clamp my jumbo binder clip to my fence and use a 1/4-in.-thick wood scrap pinched in the clip as a stop. Works like a charm! When it’s not in use, I clamp it to the cord so it’s always nearby. — John Muchow

When cutting full sheets with my circular saw, I use plastic shelving units as sawhorses. The height is just right and by using three of them, I can make cuts in any direction and the plywood is fully supported. And because the shelving units are made of plastic, I can cut right into them without worrying that they’ll damage my saw blade. Plastic shelves are available for $20 at home centers. — John Tinger. Check out these tips for making long cuts with a circular saw.
And the fact is that you can make your own patio chair with several old but still good pallets. Here we are providing a tutorial that everybody can follow easily – it is very well-written and also self-explanatory, which is great for those who are a beginner at woodworking and have never completed a DIY project before. As you don’t need to be a professional woodworker or a handyman to complete this project, so it is not a difficult task – all you need is a bit of determination!​

The rubber cushion on my old palm sander was wearing thin around the edges. Because of its age, I couldn’t find a replacement pad. As I was drinking my beverage with a foam can cover around it, I realized I could cut the foam to fit the sander and glue it on. I peeled off the old pad, cleaned the metal base and attached the foam with contact cement. Works for clamp-on as well as stick-on sanding squares! You can find can covers at discount and convenience stores. — Allen J. Muldoon


Why would you buy a costly platform bed from Ikea or somewhere else when you can make one yourself at home? Oh yes, you can. A bed is the most common furniture piece used in the house and probably the costliest one. Wouldn’t it be great if you could just make a bed of your own, without having to spend many bucks for buying one? So I am here sharing a great tutorial to help you to build a nice comfy platform bed that you can use anywhere in the house.
A bottle carrier is a bucket like carrier used to carry beer bottles and so. Yes, the same one you must have used to carry your six-pack. Drinker or not, a bottle carrier is a useful item for everyone. It can be used to carry around or store small items around a household. And it is also very easy to build one. I have several of these lying around my house. Also known as wooden beer totes, this is one wood item you will absolutely love to make. It is also super easy to build.
Figure out a simple setup for your woodworking space. You don’t need a fancy and expensive workshop or garage to start woodworking. In fact, we’ve never had a workshop or garage (though I do dream of having one haha). In our current town home, we always setup a temporary workshop table in our backyard with a pair of sawhorses and a plywood board from the home improvement store.
From the image above it seems that you do not require a big tutorial to help you to build this candle holder. All you need is a wood panel, a hook and some nails/screws and do exactly what you see in the picture. Attach the hook to the wood panel using two screws and then, attach the panel to the wall using more nails or screws. That’s it. I hope this gets the job done.

The rubber cushion on my old palm sander was wearing thin around the edges. Because of its age, I couldn’t find a replacement pad. As I was drinking my beverage with a foam can cover around it, I realized I could cut the foam to fit the sander and glue it on. I peeled off the old pad, cleaned the metal base and attached the foam with contact cement. Works for clamp-on as well as stick-on sanding squares! You can find can covers at discount and convenience stores. — Allen J. Muldoon
×