Hard to determine which stain you need in that bespattered collection of cans? An easy-to-make “stain index,” courtesy of reader Bob Jacek, solves the problem. Section off boards of your favorite woods into squares with masking tape, and apply the different stains across the width of each wood type (pine, oak, birch, etc.). When the stains are dry, brush on lengthwise your regular finishes—polyurethane, water-based polyurethane, oil, orange shellac, etc. You’ll be able to tell how each stain looks with each finish. Label each one. Use both sides of each board, and you’ll have a wooden encyclopedia of stain and finish combinations. Plus: How to stain wood evenly.
This is probably one the easiest woodworking projects you will find here. Although easy, a doormat is an equally important and useful item for households. As you can see in the image below, you will only need some 2X2 wooden boards and rope to build a simple doormat. This doormat is mostly useful for outdoor and porch. It will easily remove all the mud from your shoes with just one wipe. It is also very easy to clean and looks fabulous even if it is dirty.

There are a few things particleboard is NOT. It’s not medium density fiberboard (MDF)—a material with greater density and weight composed of more uniform particles. It’s NOT oriented strand board (OSB), a material composed of large wood chips and strands that’s structurally equivalent to plywood. It does NOT have great nail or screw holding ability, nor is it all that water resistant; water can quickly cause the material to swell and lose structural integrity. But if you need something flat and cheap for use in a dry place, particleboard will do you proud. Learn how to make a plastic laminate tabletop with a particleboard substrate.
Here’s a safe and sound way to make long cuts with a circular saw on plywood clamped to a worktable. Cut about 12 in. into the plywood, then twist a piece of duct tape into a bow tie, with up-and-down adhesive faces. Slide it in the saw kerf and press the tape down above and under the plywood. Now as you finish the cut, the trailing end can’t curl down dangerously as you saw. Hats off to Mike Connelly for simplifying this job. Check out how to make this DIY duct tape wallet.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
Often times at first glance a board looks straight and the fact that it is actually bowed or has some warping isn’t always obvious. So the trick to knowing for sure, is to hold the board up towards your face, with the other end on the ground, and look at it at a downward angle (as shown in the below photo). This method will allow you to see if it is bowing at all.
There is significant evidence of advanced woodworking in ancient Egypt.[1] Woodworking is depicted in many extant ancient Egyptian drawings, and a considerable amount of ancient Egyptian furniture (such as stools, chairs, tables, beds, chests) has been preserved. Tombs represent a large collection of these artefacts and the inner coffins found in the tombs were also made of wood. The metal used by the Egyptians for woodworking tools was originally copper and eventually, after 2000 BC bronze as ironworking was unknown until much later.[2]

This is one of those things that you never know you need unless you have one. This amazing wooden sofa sleeve works perfectly on either or both sides of a sofa set. It gives your sofa a nice look. The sleeve can also be modified to include a cup holder, mobile holder, etc. You can easily find this item on any online furniture store, but an even better idea is to build one. This way, you can make a sofa sleeve design that you actually like and make space for cup and other things.


The rubber cushion on my old palm sander was wearing thin around the edges. Because of its age, I couldn’t find a replacement pad. As I was drinking my beverage with a foam can cover around it, I realized I could cut the foam to fit the sander and glue it on. I peeled off the old pad, cleaned the metal base and attached the foam with contact cement. Works for clamp-on as well as stick-on sanding squares! You can find can covers at discount and convenience stores. — Allen J. Muldoon
I built my first platform bed by following the steps mentioned in the tutorial and the end result was everything I expected. It was as beautiful as comfortable and strong. It only cost me around $60 to build this one from the scratch. And if I can build it, anyone can. What you need is a little bit of woodworking experience and a lot of confidence. Collect the items as suggested in the video and start working now.
As soon as I came across this tutorial, I didn’t wait any longer to start building one. Some of the items you need for this project are hardwood plywood, saw, glue, nails, drilling machine, etc. The video is very easy to follow for anyone with basic woodworking knowledge and experience. The first source link also includes a step by step procedure in plain English for those, who are not comfortable enough with the video tutorial.
With an orbital sander and good sandpaper you can smooth wood evenly and easily with first-class results. When flush-sanding solid edge-banding, draw a squiggly line across the joint before sanding. The edge-banding will be slightly proud of the plywood veneer, so the pencil marks provide a visual aid to make sure that you’re sanding flat, and that you don’t sand through the plywood’s veneer. As you go, you can also test for a smooth, level transition by gently scraping your fingernails against the transition. If it’s smooth, your fingers will not catch on the seam between the two pieces
Cutting sandpaper is a quick way to dull your scissors or utility knife blade. Instead, I fastened a hacksaw blade to the edge of my workbench. I slipped a washer behind the blade at each of the mounting holes so a sheet of sandpaper to easily slides in behind the blade. I fold the paper where I want to cut, just as a reference. — Kim Boley. Try some of these storage solutions!
Instead of permanently mounting my 6-in. vise to a work-bench, I attached it to scrap plywood so I can clamp it wherever I need it. Stack two pieces of 3/4-in. plywood and screw them together with 1-1/4 in. drywall screws. Mark the vise-mounting holes on the plywood and drill 3/4-in. guide holes through both pieces. Recess the nut by drilling through the bottom sheet with a 1-in. spade bit using the 3/4-in. hole as a guide. Fasten the vise to the plywood with bolts sized to match the vise-mounting holes. If the bolt shafts are too long, cut them off with a hacksaw. — LuAnn Aiu. Plus: Learn how to use vise grips to pull nails.
Making a garden arched footbridge out of some wood boards can be fun, hard working plan and also it’s quite rewarding. We are providing the project tutorial for how to build an arched footbridge without rails or having rails. If you take your hands of work and have some basic woodworking skills you can easily build this type of bridge. While this garden bridge is too small to walk over but it can make a really stunning addition to your lush yard or garden.

I saw in the March 2019 Vol36,No.1 Iss 259. I have 2 Christian people very close to me that could likely be getting married soon . When I saw the unity cross on page one this would be the perfect gift from a parent. I would like to make it but need the plans. I do not need 3,000 or 60,000 plans I just wish to purchase the plans for the unity cross. I am a beginner so I need detail plans. Please send me information on ordering just the unity cross plans and where to purchase giant Sequoia and white oak woods. Thank you in advance for your help. I need the plans and information before April.
I got this idea from a Pinterest post. The final product looks so beautiful that I just couldn’t wait to make one for myself. This was somewhat a different experience from my other regular DIY projects as it doesn’t involve making something from scratch, but turning an existing wood piece into another one. Nonetheless, I enjoyed it very much and the final product was very satisfying. The tutorial I used is linked below.
There is no cost to use the database. Registering is not required. You should be able to browse the database and click through the links. Having said that, considering the fact there are so many browsers out there being used, this site's software might not allow some visitors to browse, it all depends on the Internet traffic, and your browser's compatibility.

Finally, as I shared in my post last week on how I learned woodworking, I learned how to use power tools by watching YouTube videos and then just trying them out for myself. I highly recommend this method to learn how to use your power tools. There are lots of videos on specific models of tools too. So, watch a few how-to videos and very importantly, review the tool manual and safety guide for your own tools. Then, go ahead and try the tool out yourself and start using it!
×